On Frequency › Guides › Read backs
RT guide
What to read back, and how to say the numbers
A read back tells the controller you heard the instruction correctly. Some things must be read back in full, every time; the numbers in them have their own way of being said. Here is what CAP 413, the UK’s radiotelephony manual, asks for.
Always read these back in full
CAP 413 para 2.69 lists the instructions you read back in full:
- taxi instructions;
- level, heading and speed instructions;
- route and approach clearances;
- the runway in use;
- clearance to enter, land on, take off on, backtrack on, cross or hold short of an active runway;
- squawks (SSR codes);
- altimeter settings, with “hectopascals” when the value is below 1000;
- VDF information, frequency changes, the type of ATS service, and transition levels.
Anything else may be acknowledged with an abbreviated read back such as “Wilco” or “Roger” (para 2.70). Roger means only that your whole message was received; Wilco means understood, and you will do it.
Your callsign goes at the end
Every read back includes your callsign (para 2.68), at the end. Use the abbreviated form (G-CD for G-ABCD) only after ATC has used it first; the full callsign is never wrong.
Wexby TowerG-CD, line up and wait runway 24
YouLine up and wait runway 24, G-CD
When the read back is wrong
If something in your read back is wrong, the controller says “negative” and gives the correct version. Read it back again (para 2.71).
Wexby TowerG-CD, QNH 1009
YouQNH 1019, G-CD
Wexby TowerG-CD, negative, QNH 1009
YouQNH 1009, G-CD
How to say the numbers
Say each digit separately in callsigns, pressure settings, flight levels, headings, wind and frequencies (paras 2.12–2.13). Nine is “niner”. Whole hundreds and thousands use HUNDRED and THOUSAND. A pressure below 1000 always takes the unit (para 3.4).
| Written | Said |
|---|---|
| QNH 1013 | Q N H one zero one three |
| QNH 993 | Q N H niner niner three hectopascals |
| QNH 1000 | Q N H one thousand |
| Heading 150 | heading one five zero |
| FL180 | flight level one eight zero |
| FL100 | flight level one hundred |
| 2500 feet | two thousand five hundred feet |
| Squawk 6500 | squawk six five zero zero |
Frequencies
Use all six figures, with “decimal”. Only when the last two figures are both zero may you give just the first four (paras 2.14–2.15).
| Frequency | Said |
|---|---|
| 118.125 | one one eight decimal one two five |
| 119.050 | one one niner decimal zero five zero |
| 122.500 | one two two decimal five |
Wexby TowerG-CD, contact Wexby Approach 126.175
YouWexby Approach 126.175, G-CD
A tip from para 2.8: leave a short gap either side of a number. It makes the number easier to copy.
Flying in Europe
Under the EU rules (SERA.8015(e)) the list is much the same: route clearances; runway clearances and instructions; the runway in use, altimeter settings, squawks, new frequencies, level, heading and speed instructions, and transition levels are always read back. Other clearances, including conditional clearances and taxi instructions, are read back or acknowledged so it is clear you have understood. Your callsign goes with every read back (SERA.14055(c)(2)).
Practise it out loud
On Frequency gives you the instruction in ATC’s voice, over the radio, and checks your read back element by element: the runway, the QNH, the squawk, your callsign, in the right order. Get one wrong and ATC says “negative”, as here.
See On FrequencySources
- CAA, CAP 413 Radiotelephony Manual, Edition 24: paras 2.8, 2.12–2.15, 2.68–2.71, 3.4.
- Regulation (EU) No 923/2012 (SERA): SERA.8015(e), SERA.14055(c)(2).
The callsigns, places and frequencies here are fictional. This guide is a summary for practice, not a substitute for CAP 413 or your instructor.