On Frequency

On Frequency › Guides › Circuit calls

RT guide

Circuit calls: downwind, base, final and go-around

The circuit is where most student pilots first use the radio for real, and where calls come fastest. The positions you report are the same at every UK aerodrome, with ATC, AFIS or an air/ground radio (CAP 413 para 4.6). Here is where each one is, and what to say.

Where you report

24 06 upwind crosswind downwind base final Left-hand circuit, runway 24 · not to scale 1 2 3 4 5 straight in
Where the reports are made. Our own drawing, after CAP 413 Figure 1.
#ReportWhen
1DownwindOn the downwind leg
2Late downwindOn downwind, past the downwind end of the runway, if you couldn’t report downwind earlier
3BaseOn base leg, if the air traffic service or the aerodrome asks for it
4FinalOn final, after the turn; the landing clearance is given here
5Long finalOn a straight-in approach, between 8 and 4 miles from touchdown

For light aircraft the circuit may be smaller, but the points stay the same. This one is left-hand; check each aerodrome’s published circuit, as some fly right-hand circuits on some runways.

Downwind, and the traffic

Before you join you get traffic information: acknowledge it, and say when you have the traffic in sight. In the circuit make the routine reports the aerodrome asks for; if ATC tells you to report at a position, answer “Wilco” (paras 4.45–4.47).

Wexby TowerG-CD, report downwind

YouWilco, G-CD

YouG-CD, downwind

Wexby TowerG-CD, number 2, follow the Piper Warrior turning base

YouNumber 2, traffic in sight, G-CD

Number, follow, extend, orbit

To fit you into the sequence, ATC gives your number, the aircraft ahead and, if needed, a delaying action. Read back the instruction (para 4.48).

Wexby TowerG-CD, extend downwind, number 2, number 1 is a Piper Warrior on base

YouExtend downwind, number 2, G-CD

Touch and go, and the last circuit

Say “touch and go” in your downwind report; the clearance comes on final. On your last circuit, report “downwind to land”. If traffic doesn’t allow a touch and go, ATC tells you to make a full stop landing (paras 4.49–4.50).

YouG-CD, downwind touch and go

Wexby TowerG-CD, runway 24, cleared touch and go, surface wind 220 9

YouRunway 24, cleared touch and go, G-CD

Final, and the landing clearance

Report “final” when you have turned onto final; “long final” if that is more than 4 miles from touchdown. The landing clearance includes the runway: read it back (paras 4.51, 4.54).

YouG-CD, final

Wexby TowerG-CD, runway 24, cleared to land, surface wind 230 11

YouRunway 24, cleared to land, G-CD

Going around

If ATC tells you to go around, reply “going around” and keep it brief: your workload is high. A VFR aircraft continues into the normal circuit unless told otherwise. If you decide to go around yourself, say so (paras 4.64–4.66).

Wexby TowerG-CD, go around, I say again, go around, acknowledge

YouGoing around, G-CD

Vacating

Stay on the tower frequency until you have vacated the runway, unless told otherwise. Taxi instructions normally come once the landing roll is complete (para 4.68).

Wexby TowerG-CD, vacate left at Charlie, report runway vacated

YouVacate left at Charlie, wilco, G-CD

YouG-CD, runway vacated

Flying in Europe

The same positions and calls are in EASA’s guidance to the EU rules (Appendix 1 to AMC1 SERA.14001). One UK difference: a solo student says STUDENT before the callsign on first contact; under SERA there is no STUDENT prefix.

Fly a circuit out loud

On Frequency’s Circuits module has the calls as cards and a drill, then a circuit flight at Wexby: a touch and go, then a full stop, with ATC sequencing you, sometimes extending your downwind or sending you around. Your calls are checked as you make them, and the aerodrome chart shows where you are.

See On Frequency

Sources

The callsigns, places and frequencies here are fictional. This guide is a summary for practice, not a substitute for CAP 413 or your instructor.